Iron ore pellet is a kind of agglomerated fines which has better tumbling index as compared to that of parent ore and can be used as a substitute used in blast furnaces in countries where lump ore is not available. India's iron ore export basket used to comprise predominantly of iron ore fines (almost to the tune of 80% of total iron ore exports) largely because of the lucrative market it catered to globally and secondly as the domestic market for iron ore fines as a ready-made feed for sintering/palletisation was at a still-nascent stage. However, over time with significant changes in the domestic iron ore market and given the increasing uncertainties in global steel market courtesy the slowdown in Chinese demand, India’s iron ore export has taken a hit. At the same time, the perception that iron ore fines
can be gainfully utilized by offering a ready-to-use feed material in the form of pellets whose use in turn, leads to substantial economic gains over time and given the shortage of quality iron ore lump.
Product Specification
(Chemical Composition on DRY basis)
Fe: 65% Basis, 64% below rejection
SiO2: 2.5-3% Max
P: 0.045
S: 0.010
CaO: 0.8 Max
MgO: 0.10 Max
Moisture: 1 PCT
Physical Specification
Size: 5-18 MM 98 PCT
BELOW 5 MM 1 PCT
ABOVE 18 MM 1 PCT
Tumbler Index (Above 6 MM): 95%
Abrasion Index (Below 0.5 MM) : 2-3%
Cold Compression Strength : 230-250 KG/PELLET
Bulk Density: 2.2 T/M3
POROSITY: 20-23 PCT
All Ferrous Raw Material is low in impurities contents (silica, alumina, potash) and presents a very high reactivity allowing an important reduction in energy consumption and very high productivity in the furnace.
We can supply Lumpy ore and Concentrates Having Cr Content from 29% up to highest form of purity almost 60% with any particle size ranging from 150 micron to #325 Mesh or lumps up to 50mm of different origins
Chromite is also used as a refractory material, because it has a high heat stability. The chromium extracted from chromite is used in chrome plating and alloying for production of corrosion resistant super alloys, nichrome, and stainless steel.
All Ferrous Raw Material is low in impurities contents (silica, alumina, potash) and presents a very high reactivity allowing an important reduction in energy consumption and very high productivity in the furnace.
India offers high quality Chromite ore with low silica, through aluminium thermic process we are able to achieve highest quality of metal recovery with ultra-low carbon content.
Product Specification
Cr%- 70-75% Minimum
Si%- 1.3-1.5 max
C%- 0.050-0.090 max
S%- 0.009
P%- 0.009
We source the highest quality Manganese Ore from Zambia of grade from 34% up to 52% purity. Mostly lumpy and sizes varies from 30 mm up to 60 mm. Manganese ore is mixed with steel to improve hardness which is essential in the manufacturing of construction materials. It has a similar application when alloyed with aluminium and helps to reduce corrosion and is used in the manufacturing of beverage cans.
Ore with high content of Mn is intended for the production of HCFeMn and its derivatives. Our grade with its high Manganese content and low iron content has been specifically designed for production of High Carbon Ferro Manganese (HCFeMn) and its by-products.
All Ferrous Raw Material is low in impurities contents (silica, alumina, potash) and presents a very high reactivity allowing an important reduction in energy consumption and very high productivity in the furnace.
Steel billets are the second-stage (Semi Finished) product of steel production. They are hot-rolled and are taken out directly during casting process of steel. They are highly ductile and soft and produced in a square cross-section of area less than 36 sq.inches (230 sq. cm). They fall under the category of semi-finished casting products. Their final products involve bars, rods, tubes, pipes, wire and wire products.
Product Specification
Carbon – 0.14 to 26 %
Sulphur – 0.05% max
Phosphorus - 0.05% max
Silicon – 0.05% to 0.40% max
Manganese – 0.50Min to 0.80%
Sizes
100X100 up to 130X130Length: 5.8 Meters for containers
For Bulk Shipments length is up to 6 meters
We have a dedicated captive continuous type Ball Mill facility for minerals and metals. The Mill can grind Particle size ranging from 150 micron to 400 mesh pass.
The main minerals covered are bauxite, soap stone, calcite, kaolin, ball clay and china clay. The grinding of minerals is done using locally available equipment such as pulverize, material handling equipment, sieving machines, packing machines, etc. It is assumed that the average production capacity will be 3000 MT per month.
